混凝土試模由底模板、側模板隔板軸、支架活節螺栓和蝶形螺母等零件組成。是由底模板、側模板隔板軸、支架活節螺栓和蝶形螺母等零件組成底模板是由高強度的鑄鐵制成，側模板，隔板是用較硬的碳結鋼支撐，支架固定在低模板上。活節螺栓用圓柱銷聯結在支架上，并可饒圓柱銷軸線轉動。裝配時，先將兩塊側模板相對垂直放在底模板平面上，用套在活節螺栓上的軸插入側模板兩端槽內，稍加固定，然后將隔板插入側模板的槽內，對正兩塊側模板，保證模腔成正方形，再邊擰緊軸上的蝶形螺母，邊用木榔頭輕擊各板上側面，使其下側再在同一平面上，然后再擰緊活節螺栓上的蝶形螺母，保證各板下側面與低模板平面貼近。

　　混凝土試模的使用注意事項

　　每次做試塊之前，在試模腔內壁涂薄薄一層機油或脫模劑。

　　拆卸時，下擰松活節螺栓上的蝶形螺母，在擰松軸上的蝶形螺母，連同活節螺栓脫離側模板槽內，即可拆去側模板，每次脫模后，應極力擦凈各零件表面的涂渣，并涂上防銹油。

　　混凝土試模的檢驗方法

　　1、用感官檢查混凝土試模，要符合由鑄鐵或鋼制成，內表面應機械加工平整光滑，并不應有任何砂眼或缺陷。

　　2、用游標卡尺，測量混凝土試模每邊長度及直徑，其值應符合：100×100×100試模每邊100±0.2mm；

　　150×150×150150±0.2mm。

　　3、用游標卡尺測量混凝土試模對角線，其值應相差不超過1mm。